Maintaining and Troubleshooting Your 3D Printer

Maintaining and Troubleshooting Your 3D Printer
Author :
Publisher : Apress
Total Pages : 509
Release :
ISBN-10 : 9781430268086
ISBN-13 : 1430268085
Rating : 4/5 (86 Downloads)

Book Synopsis Maintaining and Troubleshooting Your 3D Printer by : Charles Bell

Download or read book Maintaining and Troubleshooting Your 3D Printer written by Charles Bell and published by Apress. This book was released on 2014-09-17 with total page 509 pages. Available in PDF, EPUB and Kindle. Book excerpt: Maintaining and Troubleshooting Your 3D Printer by Charles Bell is your guide to keeping your 3D printer running through preventive maintenance, repair, and diagnosing and solving problems in 3D printing. If you’ve bought or built a 3D printer such as a MakerBot only to be confounded by jagged edges, corner lift, top layers that aren’t solid, or any of a myriad of other problems that plague 3D printer enthusiasts, then here is the book to help you get past all that and recapture the joy of creative fabrication. The book also includes valuable tips for builders and those who want to modify their printers to get the most out of their investment. Good fabrication begins with calibration. Aligning the print bed to support deposition of medium in three dimensions is critical. Even off-the-shelf machines that are pre-built must be aligned and periodically realigned throughout their life cycle. Maintaining and Troubleshooting Your 3D Printer helps you achieve and hold proper alignment. Maintaining and Troubleshooting Your 3D Printer also helps with software and hardware troubleshooting. You’ll learn to diagnose and solve firmware calibration problems, filament and feed problems, chassis issues, and more. Finally there are regular maintenance and enhancements. You’ve invested significantly in your 3D printer. Protect that investment using the guidance in this book. Learn to clean and lubricate your printer, to maintain the chassis, and know when realignment of the print bed is needed. Learn ways to master your craft and improve the quality of your prints through such things as post-print finishing and filament management. Don’t let the challenges of 3D printing stand in the way of creativity. Maintaining and Troubleshooting Your 3D Printer by Charles Bell helps you conquer the challenges and get the most benefit from your expensive investment in personal fabrication.


Maintaining and Troubleshooting Your 3D Printer Related Books

Maintaining and Troubleshooting Your 3D Printer
Language: en
Pages: 509
Authors: Charles Bell
Categories: Computers
Type: BOOK - Published: 2014-09-17 - Publisher: Apress

DOWNLOAD EBOOK

Maintaining and Troubleshooting Your 3D Printer by Charles Bell is your guide to keeping your 3D printer running through preventive maintenance, repair, and dia
3D Printing Basics for Entertainment Design
Language: en
Pages: 641
Authors: Anne E. McMills
Categories: Performing Arts
Type: BOOK - Published: 2017-10-12 - Publisher: Taylor & Francis

DOWNLOAD EBOOK

Affordable 3D printers are rapidly becoming everyday additions to the desktops and worktables of entertainment design practitioners – whether working in theat
3D Printing
Language: en
Pages: 183
Authors: Tyler Kerr
Categories: Technology & Engineering
Type: BOOK - Published: 2022-11-21 - Publisher: Springer Nature

DOWNLOAD EBOOK

This book is an introduction to the wide and varied world of 3D printing—an incredible technology used across an ever-growing list of industries. As 3D printi
3D Printing
Language: en
Pages: 191
Authors: Sara Russell Gonzalez
Categories: Language Arts & Disciplines
Type: BOOK - Published: 2016-05-08 - Publisher: Rowman & Littlefield

DOWNLOAD EBOOK

Planning and implementing a 3D printing service in a library may seem like a daunting task. Based upon the authors’ experience as early adopters of 3D technol
3D Printing with MatterControl
Language: en
Pages: 176
Authors: Joan Horvath
Categories: Computers
Type: BOOK - Published: 2015-09-14 - Publisher: Apress

DOWNLOAD EBOOK

In 3D Printing With MatterControl, Joan Horvath and Rich Cameron, the team behind Mastering 3D Printing, explain step-by-step how to use the MatterControl progr